深圳市美华安规仪器有限公司
地址: A. 深圳光明新区光明
圳美311号/518107
B. 东莞大岭山镇渭
溪路/523829
热线: 155-0203-6348;
136-1283-4185
电话: 0755-3288-5887
传真: 0755-3288-5887
Q Q: 1-4848-7-5858;
4-9327-8805
邮箱: sm#ag17.wang
okgang#163.com
(#请改@)
官网: www.ag17.wang
论坛: bbs.ag17.wang
ASTM D412-06a(2013)Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D412中文版:http://www.ag17.wang/safety/ASTM_D412-06a(2013).html
MORE D11.10 STANDARDSRELATED PRODUCTSSTANDARD REFERENCESFIND LABS
Significance and Use
5.1 All materials and products covered by these test methods must withstand tensile forces for adequate performance in certain applications. These test methods allow for the measurement of such tensile properties. However, tensile properties alone may not directly relate to the total end use performance of the product because of the wide range of potential performance requirements in actual use.
5.2 Tensile properties depend both on the material and the conditions of test (extension rate, temperature, humidity, specimen geometry, pretest conditioning, etc.); therefore materials should be compared only when tested under the same conditions.
5.3 Temperature and rate of extension may have substantial effects on tensile properties and therefore should be controlled. These effects will vary depending on the type of material being tested.
5.4 Tensile set represents residual deformation which is partly permanent and partly recoverable after stretching and retraction. For this reason, the periods of extension and recovery (and other conditions of test) must be controlled to obtain comparable results.
1. Scope
1.1 These test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers. These methods are not applicable to ebonite and similar hard, low elongation materials. The methods appear as follows:
Test Method A—Dumbbell and Straight Section Specimens
Test Method B—Cut Ring Specimens
Note 1—These two different methods do not produce identical results.
1.2 The values stated in either SI or non-SI units shall be regarded separately as normative for this standard. The values in each system may not be exact equivalents; therefore each system must be used independently, without combining values.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
ASTM Standards
D1349 Practice for Rubber--Standard Temperatures for Testing
D1566 Terminology Relating to Rubber
D3182 Practice for Rubber--Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
D3183 Practice for Rubber--Preparation of Pieces for Test Purposes from Products
D3767 Practice for Rubber--Measurement of Dimensions
D4483 Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries
E4 Practices for Force Verification of Testing Machines
ISO Standards
ISO37 Rubber, Vulcanized and Thermoplastic Determination of Tensile Stress-Strain Properties Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.
Keywords
Deformation - Dumbbell Specimens - Elongation - Mechanical Properties - Ring Specimens - Rubber - Straight Section Specimens - Tensile Strength - Tensile Test - Test Specimens And Test Engines - Thermoplastic Elastomers - Vulcanized Rubber - Yield Point
ICS Code
ICS Number Code 83.060 (Rubber)
UNSPSC Code
UNSPSC Code 13101601(Vulcanized rubber); 13101606(Thermplastic rubber)
Referencing This Standard
DOI: 10.1520/D0412-06AR13
ASTM International is a member of CrossRef.
仪器商城:www.17-18.cn
安规仪器网/美华安规仪器---追崇原创、重视知识产权和尊重劳动成果,也是行业发展主旨,禁止盗链、非取采集、复制及转载等行为,一经发现保留追责权力。有关标准和技术探讨,请联络邮箱:1484875858#qq.com(#改为@),QQ1484875858